来源：本站
江森M9203 3NM弹簧复位驱动器资料下载
The M9203 Series Electric Spring Return Actuators are direct-mount actuators.
These bidirectional actuators do not require a damper linkage, and are easily installed on round shafts or square shafts using the standard shaft clamp included with the actuator.
A single M9203 Series Electric Spring Return Actuator provides 3 Nm running and spring return torque.
An integral line voltage auxiliary switch, available only on the M9203-xxB-1(Z) models, indicates end stop position, or performs switching functions within the selected rotation range.
M9203 Series Actuators provide 95° of rotation. A graduated scale from -5° to 90° and a position indicator provide visual indication of stroke. When power fails during service, the mechanical spring return system provides rated torque to the connected equipment, returning it to the home position.
The series includes the following control options:
• ON/OFF, 24 V, 100 to 240 VAC power
• ON/OFF and Floating Point, 24 V power
• Proportional, 24 V power, for 0(2) to 10 VDC or 0(4) to 20 mA Control Signal
■■ 3■Nm■Rated■Torque
Provides high torque in a compact package size to expand the range of damper applications in HVA system.
■■ Direct-Coupled■Design
Requires non crankarm or linkage and is capable of direct mounting to a shaft up to 12 mm diameter and centered on a 12 mm shaft.
■■ Reversible■Mounting
Provides either clockwise or counterclockwise operation.
■■ Electronic■Stall■Detection
Protects from overload at all angles of rotation. Power consumption is reduced in holding mode.
The actuator may be stalled anywhere in its rotation range without the need for mechanical end switches.
■■ Double-Insulated■Construction
Eliminates need for electrical ground connection for regulatory agency compliance.
■■ Microprocessor-controlled■Brushless■DC■Motor■(-AGx■and■GGx■types)
Provides constant runtime independent of torque.
■■ External■Mode■Selection■Switch■(-AGx■and■-GGx■types)
Permits control logic reversal for Floating Control (-AGx types). Permits calibration, input signal range selection and control logic reversal for Proportional Control (-GGx types).
■■ Integral■Cables■with■Colored■and■Numbered■Conductors
Simplify installation and field wiring.
■■ Optional■Integrated■Auxiliary■Switch
Provides one integrated, line-voltage-capable Single-Pole, Double-Throw (SPDT) switch with continuously adjustable switch point. Facilitates safety interfacing or signaling.
■■ Override■Control■(Proportional■Models■Only)
Supports manual control system override applications through field wiring.
■■ Manufactured■under■International■Standards■Organization■(ISO)■9001■Quality■Control■Standards■
Installation
The M9203 Series Proportional Electric Spring Return Actuators mount directly to the surface in any convenient orientation
using two No. M3.5 x 9.5 mm self drilling sheet metal screws and the anti-rotation bracket (parts included with the actuator). No additional linkages or couplers are required. Electrical
connections are color coded and identified with numbers
Clockwise (CW) Spring Return Direction – Counterclockwise (CCW) Powered Operation
For CW spring return direction, mount the actuator to the damper shaft so that Side B of the actuator is away from the damper as illustrated in Figure 2. With power applied, the actuator drives CCW from the 0° position and spring returns CW.
cable identifies the electrical connections and wiring details are included on the actuator housing.
This Spring Return Actuators can be easily installed on dampers with round shafts from 6 to 12 mm or square shafts from 6
to 8 mm using the standard shaft coupler included with the actuator. If the damper shaft extends less than 84 mm, see the Removable Coupler section for further instructions. If the
damper shaft extends less than 20 mm, install a shaft extension recommended by the damper manufacturer.
Counterclockwise (CCW) Spring Return Direction
- Clockwise (CW) Powered Operation
For CCW spring return direction, mount the actuator to the damper shaft so that Side A of the actuator is away from the damper as illustrated in Figure 1. With power applied, the actuator drives CW from the 0° position and spring returns CCW.
Removable Coupler
If the damper shaft extends less than 84 mm, mount the coupler on the face of the actuator closest to the damper.If the damper shaft extends less than 20 mm, a shaft extension is required to mount the actuator.
To change the coupler’s position, see Figure 3 and proceed as follows:
1. Mount the coupler on either Side A or Side B of the actuator as determined by the shaft length.
2. Snap the locking clip securely into the coupler retention groove to retain the coupler.
